QBY Air-Operated Double-Diaphragm Pump

QBY Air-Operated Double-Diaphragm Pump

The QBY air-operated diaphragm pump is a positive-displacement pump powered by compressed air. It has two pump chambers, each fitted with a flexible diaphragm. The diaphragms are connected by a central shaft and reciprocate in unison as the air-distribution valve alternately supplies air to the two air chambers.
The pump's main components include the casing, diaphragms, valve balls and seats, air-distribution valve and silencer. As the diaphragms move, the pump-chamber volumes change. Inlet and discharge check valves open and close in sequence to draw in and discharge liquid.
Pošaljite upit
Opis

 

The QBY air-operated diaphragm pump is a positive-displacement pump powered by compressed air. It has two pump chambers, each fitted with a flexible diaphragm. The diaphragms are connected by a central shaft and reciprocate in unison as the air-distribution valve alternately supplies air to the two air chambers.

The pump's main components include the casing, diaphragms, valve balls and seats, air-distribution valve and silencer. As the diaphragms move, the pump-chamber volumes change. Inlet and discharge check valves open and close in sequence to draw in and discharge liquid.

Wetted-part materials can include aluminium alloy, cast iron, 304/316/316L stainless steel, reinforced polypropylene (PP), PVDF and PTFE. Diaphragms are available in materials such as NBR, chloroprene rubber, FKM and PTFE.

Model designation example: QBY-40

  • Air-operated diaphragm pump series.
  • 40: Inlet and outlet diameter, in millimetres.

Some manufacturers include additional information, such as maximum flow or head, in the model designation.

 

 

1. Compressed-air drive

The pump uses compressed air rather than an electric motor at the pump, which can be useful where electrical equipment is unsuitable or compressed air is already available. Actual energy use depends on the pump duty and the efficiency of the plant's compressed-air system.

 

2. Diaphragm separation and leakage control

The diaphragm separates the pumped liquid from the air-drive mechanism, avoiding a conventional rotating shaft seal through the product-contact area. This can help control leakage when handling hazardous or valuable liquids, provided the diaphragm and wetted materials are compatible with the medium.

 

3. Handles some solids and viscous liquids

The pump has no rotary impeller, and its passages can handle some solids, fibres and viscous liquids. The source gives a viscosity limit of up to 30,000 cP and a particle size of up to 10 mm; actual limits depend on the model, liquid properties and valve configuration.

 

4. Dry-running tolerance

Some QBY pumps can tolerate dry running, but allowable duration and conditions vary. Follow the manufacturer's guidance, particularly for operation at high cycle rates or with abrasive media.

 

5. Self-priming capability

The stated self-priming height is up to 7 m. Achievable suction lift depends on factors such as liquid viscosity, temperature, suction-line losses, valve condition and pump size.

 

6. Adjustable flow and pressure

Flow can generally be adjusted by regulating the air supply. Discharge pressure depends on air pressure, the pump's pressure ratio, system resistance and the operating point. Use the manufacturer's limits and suitable pressure-control equipment.

7. Gentle pumping for shear-sensitive liquids

The reciprocating diaphragm action can be suitable for some shear-sensitive products, including polymer solutions, emulsions and food pastes. The℃of shear depends on the pump design, speed and liquid characteristics.

8. Submerged operation may be possible

Some configurations can be operated submerged, provided the materials are compatible and the exhaust-air arrangement is suitable. Confirm submergence requirements with the manufacturer.

9. Multiple material options

Pump bodies, diaphragms, valve balls and seats are available in different materials to suit the chemical, temperature and wear conditions of the application.

10. Simple maintenance

The pump has relatively few moving parts. Diaphragms, valve balls and valve seats are common wear parts and can generally be replaced during routine maintenance.

 

 

The QBY series is used for transferring liquids that may be viscous, solids-bearing or corrosive, including:

  • Crude oil, heavy oil, coal tar, gasoline, diesel, solvent oil, acids, alkalis, organic solvents, emulsions and liquid chemicals.
  • Paint, coatings, ink, pigment slurry, resin solutions, adhesives and glues.
  • Ceramic slurry, glaze, cement slurry, putty and gypsum slurry.
  • Chocolate, syrup, honey, jam, yeast slurry, edible oil, spent grain and soy sauce, subject to hygienic design and relevant approvals.
  • Ointments, creams, shampoo, facial cleanser and cosmetic emulsions, subject to process requirements.
  • Sludge, oily wastewater, electroplating wastewater and acid or alkali waste; also used as a filter-press feed pump and for chemical dosing.
  • Mineral slurry, flotation reagents, tailings, electrolytes and pickling solutions.
  • Pulp, black liquor, dye slurry and textile wastewater.
  • High-purity chemicals, electronic-grade solvents and polishing slurries, with suitable materials and cleanliness controls.
  • Printing ink, varnish and laminating adhesive.
  • Oily bilge-water discharge and cargo transfer, subject to vessel and service requirements.
  • Temporary drainage, emergency wastewater transfer and mobile pumping systems.

 

 

1. Operating Principle

Compressed air enters the pump through the air-distribution valve, which alternately supplies the left and right air chambers.

When air enters one side, it pushes that diaphragm toward its pump chamber. The chamber volume decreases: the inlet ball valve closes, the discharge valve opens and liquid is expelled. At the same time, the connecting shaft pulls the opposite diaphragm back, increasing the volume of the other pump chamber. Its inlet valve opens and liquid is drawn in.

When the air-distribution valve switches over, the cycle reverses. The two chambers alternate between suction and discharge to provide pumping action.

 

2. Construction

  • Air-distribution valve

Each pump chamber has an inlet and a discharge valve that function as check valves. The air-distribution valve alternates compressed-air supply between the two air chambers.

 

3. Compressed-Air Supply

The stated working-air pressure is 0.2–0.7 MPa. The air supply should be clean, dry and regulated. An air filter and pressure regulator are commonly used. Fit a lubricator only when the pump manufacturer specifies one; some air-distribution systems are designed to operate without added oil.

Air consumption varies with pump size, cycle rate, air pressure and operating conditions.

 

4. Wetted-Part Materials

Aluminium alloy, cast iron, 304 / 316 / 316L stainless steel, reinforced PP, PVDF, PTFE

Stainless steel, ceramic, PTFE, rubber-coated steel ball

 

5. Stated Operating Range

0.5–50 m³/h across the series

0–0.84 MPa / 0–84 m, as stated

Working-air pressure

0.2–0.7 MPa

Up to 30,000 cP, as stated

−20℃ to 150℃, depending on diaphragm and wetted materials

Self-priming height

Up to 7 m, as stated

1–10 mm, depending on pump size

10–100 mm

0–60 cycles/min, depending on air supply and pump model

 

 

product-1108-739

 

 

 

Air-supply pressure (MPa)

Self-priming height (m)

QBY-10

0.8

0.6

0.2-0.8

1.5

0-7

10

0.3

8

QBY-15

1.5

0.6

0.2-0.8

2

0-7

15

0.5

15

QBY-20

2.5

0.6

0.2-0.8

2.5

0-7

20

0.6

20

QBY-25

3

0.6

0.2-0.8

3

0-7

25

0.6

25

QBY-32

4.5

0.6

0.2-0.8

4

0-7

32

0.8

35

QBY-40

6

0.6

0.2-0.8

4.5

0-7

40

0.8

45

QBY-50

12

0.6

0.2-0.8

6

0-7

50

1.2

65

QBY-65

18

0.6

0.2-0.8

8

0-7

65

1.5

100

QBY-80

24

0.6

0.2-0.8

10

0-7

80

2

150

QBY-100

36

0.6

0.2-0.8

12

0-7

100

2.5

200

QBY-125

50

0.6

0.2-0.8

15

0-7

125

3.5

280

QBY-150

80

0.6

0.2-0.8

18

0-7

150

5

400

QBY-200

120

0.6

0.2-0.8

22

0-7

200

8

600

If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.

Popularni tagovi: qby air-operated double-diaphragm pump, China qby air-operated double-diaphragm pump manufacturers, factory

Pošaljite upit